Anti-Crawl
PHOTOELECTRIC BEAM SENSOR PB-IN-100AT
Outdoor 100m (330 ft.)
The TAKEX Intelligent-Quad photoelectric beam, PB-IN-100AT has been designed for high security applications where attempts to crawl through a portion of the photo beam create an alarm event instead of no alarm.
Transmitters project double modulated beams that differ in pulse pattern from upper and lower parts.
Through CPU processing, the upper receiver selects the beam from the upper transmitter and the lower receiver selects the beam from the lower transmitter, allowing for an AND-gated or an OR-gated system.
Data Download
Feature
BASIC OPERATION
The following basic operation is required for the purpose of preventing lost alarms from intrusion by crawling without burdening the system with false alarms via small animals.
* Lower or upper beams interrupted
An alarm is not output by instantaneous beam interruption, but an alarm is output when the interruption continues during a set response time.
The response time can be tailored to prevent intrusion by crawling while at the same time avoiding false alarms due to small animals.
* ALL beams interrupted
Same as PB-IN-HFA series, an alarm is output when beam interruption continues during the response time.
FOUR FREQUENCY SELECTION
4 separate choices of frequency avoids cross-talk in stacked or long linear installations.
DUAL RESPONSE TIME SYSTEM
Two individual response times are provided for separate adjustment of AND/OR gates.
This enables detection of intruders, but minimizes false alarms.
BEAM TRANSMISSION STRENGTH SELECTION
2 levels of beam transmission strength which can be set to suit the protection distance.
AUTO-GAIN LOCK
Optimal sensitivity gain is automatically set at any coverage distance up to the maximum protection distance. Auto-Gain lock is easily confirmed by sound check.
EASY BEAM ALIGNMENT
・Audible signal for alignment [Utility model] ...
An alignment tone aids in quick set-up beams. The tone becomes maximum at peak of beam level.
・Beam selector ... Upper and lower beam alignment can be adjusted without using a shading plate.
・Sensitivity attenuation LED ... Lights when beam level is attenuated, which shows low sensitivity.
・Monitor jack output
・Target color
PROGRAMMED AGC
Sensitivity is automatically increased in bad weather to contend with fog, heavy rain, frost or snow.
ENVIRONMENTAL MODULE BUILT-IN
Environmental trouble signal is sent when beam reception level is reduced below an acceptable level.
PROTECTION AGAINST FROST/DEW
As a special hood is attached on sensor cover, beam protection continues without interruption even when the cover is screened by frost or dew.
Specification
| Model | PB-IN-100AT |
|---|---|
| Detection system | Near infrared beam interruption system (TR,-RE 4 beams simultaneous interruption or upper 2 beams interruption or lower 2 beams interruption) |
| Infrared beam | Double modulation pulsed beam by LED |
| Protection distance | Outdoor 100m (330') or less |
| Max. arrival distance | Tenfold 1000m (3300') |
| Response time | Dual response time system 35-500msec. (AND gated) 100,200,300,500msec.(OR gated) |
| Power supply | 12V to 30V DC(non-polarity) |
| Current consumption | 57mA or less |
| Alarm output | Dry contact relay output C Reset:Interruption time+off-delay(approx. 1.5 sec.) Contact capacity:30V AC/DC, 0.25A or less |
| Environmental output | Dry contact relay:C Contact operation:Output when weather condition gets worse Contact capacity:30V AC/DC, 0.25A or less |
| Tamper output | Dry contact relay:N.C. Contact operation:Output when transmitter or receiver cover is detached Contact capacity:30V AC/DC, 0.1A or less |
| Alarm LED | Red LED(receiver)lights when an alarm is initiated |
| Sensitivity attenuation LED | Red LED(receiver)lights when beam reception is attenuated |
| Functions | Modulated beam frequency selection,Tone indicator, Environmental module, Beam power selection, Beam selector, Programmed AGC, Auto-gain lock function, Monitor jack,Target color. |
| Beam adjustment | Horizontal: +/-90°, Vertical: +/-10° |
| Ambient temperature range | -35C to + 66C (-31F to + 151F) |
| Mounting position | Outdoor |
| Wiring | Terminals |
| Weight | Transmitter:1200g(42 oz) Receiver :1300g(45.5oz) |
| Appearance | PC resin(wine red) |
* The specifications are subject to change without notice.
